Leading 10 usual forklift crashes ， forklift procedure must take notice of these issues ！.

Leading 10 usual forklift crashes ， forklift procedure must take notice of these issues ！.

Blog Article

Don't take too lightly the forklift at the office. If the procedure is bad, there will certainly be serious accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift freight blocked the motorist's view, and the individual ahead might not be discovered, leading to a rolling mishap.
Situation 2: In order to maintain the balance of the forklift when lifting hefty items, the staff members utilized their body weight as the weight, which nearly triggered casualties.
Situation 3: The width of the forklift cargo goes beyond the allowed size of the path and hangs on the roadside shelf, which virtually creates an mishap.
Situation 4: Forklift is speeding and rolls over during a turn.
Situation 5: The forklift motorist did not observe the pedestrian, and the pedestrian did not observe the forklift.
Instance 6: The forklift raises the workers unlawfully, the forklift driver does not use the safety belt, the forklift lifter drops and the motorist is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not wear a safety belt and dropped from the car when it rolled over and was squashed.
Forklift operation need to take notice of these issues ：.

Beginning.
1. Before starting, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and then start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) scale need to be safe prior to starting.
3. When the forklift begins with a lots, the vehicle driver must initially verify that the lots is steady and reliable.
4. The begin must be slow-moving and constant.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When getting in and leaving the work website or while driving, beware that there will be no barriers in the sky. When the load is traveling, the fork has to not be increased expensive, which will certainly impact the security of the forklift. .
3. After discharging, the fork must be reduced to the regular driving position before driving. .
4. When turning, if there are pedestrians or vehicles close by, the driving signal ought to be issued initially. High-speed sharp turns are prohibited. High-speed doglegs will certainly trigger the automobile to shed lateral stability and tip over. .
5. When the forklift is downhill, it is purely restricted to switch off the flame and slide, and it is prohibited to brake suddenly while driving with loads unless there are special conditions.
6. When the forklift is running, it has to obey the traffic rules in the factory and should keep a specific security distance from the automobile ahead. .
7. When the forklift is running, the load has to be in the lowest setting that does not prevent the driving, and the gantry must be effectively slanted back. The tons shall not be increased except when stacking or loading. .
8. The height of the lots have to not obstruct the vehicle driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when turning around.
9. It is restricted to switch on the ramp, nor to drive throughout the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when going into the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to depend on the fork to hold things and play a balancing role. .
12. If problems are located, they will be repaired and reported in a prompt way, and they will never ever operate with diseases or hide them.

packing and unloading.
1. When fork-loading things, the range between both forks ought to be adjusted as required to make the tons of both forks well balanced and not skewed, and one side of the thing ought to protest the shelf. .
2. It is forbidden to collaborate with a single fork or make use of a fork top or pull. In unique scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of loading and dumping products, the forklift has to be braked with the brake. .
4. The rate of the car need to be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and injure people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as feasible under the lots, and it ought to be kept in mind that the fork tip must not touch other products or things. The load must be maintained with minimal back tilt of the gantry to ensure that the lots does not slide in reverse. The pole can be tilted ahead a little when the lots is lowered to enable very easy placement of the tons and removal of the forks. .
6. It is restricted to fork goods at high speed and hit tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so regarding avoid the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to utilize forks to lift workers to take part in high-altitude procedures to avoid high-altitude falling accidents. .
9. It is not allowed to utilize the brake inertia to slip, put, round or roll items. .
10. It is not enabled to make use of forks to select, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the things on the fork are in the air. Prior to leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the parking brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go Stand-on Electric Pallet Stacker beyond 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance needs to be examined, and gas, lubing oil and cooling water ought to be included.
2. Examine the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leakage should additionally be examined Stand-on Electric Pallet Stacker and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You have to examine before leaving the vehicle;.
2. When you encounter a person in front of you during driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free switching";.
6. Adding and down the slope must be slow and consistent, and no turning on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they must take the turning around exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Car parking is not allowed under the list below problems.
1. Contours, slim roads, railway crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the area with the same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844